1. Litter Robot III - Dump Position Fault - RobotShop Community
May 3, 2020 · My litter robot 3 recently started flashing the blue-yellow-green “cannot find dump position” error code and won't cycle after the cats use it.
Hi! I require your help regarding a problem I’m encountering. Description: My litter robot 3 recently started flashing the blue-yellow-green “cannot find dump position” error code and won’t cycle after the cats use it. If I press “reset” and then “cycle” it will cycle as normally (or almost as normally, see below) but when it returns to the home position the same error lights start flashing again. One thing I have noticed is that, when it is cycling and it reaches the end of its first turn, th...
2. Litter-Robot 3: All three lights flashing (Globe position fault)
Check for excess litter inside the globe. Using more than 10 lbs (4.5 kg) of litter can strain the motor, causing a globe position or over-torque fault. Make ...
Find solutions for your Litter-Robot 3's three lights flashing position sensors issue. Fix issues with your Connect Upgrade Kit today!
3. Litter robot 3 - dump position fault - RobotShop Community
More results from community.robotshop.com
I just received my new litter robot 3 today. It’s giving an error ‘dump position fault’ after making a cycle. I then do another cycle and this time it does not give an error. Am I missing anything? As I said this is brand new received today. Thanks
4. Litter-Robot 4: Red light bar with partial white flashing (Globe position)
If your unit displays a red light bar with partial white flashing, this indicates that the unit did not detect the globe position during its previous cycle.
Visit for solutions if your Litter-Robot 4 has a red light bar with a partial white flashing globe. Get instant support and fixes today.
5. Extracting status message and TTS from litter-robot - automation
Nov 9, 2022 · I am seeking guidance if there is a way to grab the current status code message (for example: “Clean Cycle Complete”), and just use that.
alias: Test - Litter Robot description: "" trigger: - platform: state entity_id: - sensor.litter_robot_status_code condition: [] action: - service: tts.google_translate_say data: entity_id: media_player.aaron_s_speakers message: [litterrobot__status_code message here] cache: true mode: single I wanted to create a TTS automation that would trigger every time the [sensor.litter_robot_status_code] changes. The trigger works, however, I need to figure out how...
6. Litter-Robot 3: Fixing the globe magnets
Troubleshooting your disassembled Litter-Robot 3 Globe? Our guide helps you check magnet positions and correct errors for a smoothly functioning unit.
7. Litter-Robot 4: Red with partial yellow flashing (Over-torque fault)
Ensure the seal strips around the dump port are not peeling up or accumulating litter. This could impact the rotation of the globe. You may purchase replacement ...
Get solutions for your Litter-Robot 4 red with partial yellow flashing over-torque fault. Find easy fixes here! Explore our support page now.
8. Litter Robot III - Flashing lights sequentially or flashing all at once
If the lights on the control panel blink, right to left, left to right or together, the problem is still the same: the robot has failed to track the position of ...
Most of you are here because there are 3 flashing lights on your Litter-Robot's control panel. Sometimes this problem is caused by a faulty power supply or the motor itself. If even after checking the set screw on the motor and checking the voltage on the power supply with a multimeter, the lights…
9. https://raw.githubusercontent.com/dcmeglio/hubitat...
/** * Litter-Robot * * Copyright 2020 Nathan Spencer * * Licensed under the ... 3 minuts: cleanCycleWaitTimeMinutes = 3 (hexadecimal representation of ...
/** * Litter-Robot * * Copyright 2020 Nathan Spencer * * Licensed under the Apache License, Version 2.0 (the "License"); you may not use this file except * in compliance with the License. You may obtain a copy of the License at: * * http://www.apache.org/licenses/LICENSE-2.0 * * Unless required by applicable law or agreed to in writing, software distributed under the License is distributed * on an "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the License * for the specific language governing permissions and limitations under the License. * * * Known commands that can be called: * C - start cleaning cycle: unitStatus changes from RDY to CCP; upon completion, cycleCount += 1 and unitStatus briefly goes to CCC and panelLockActive = 1 then typically returns to unitStatus of RDY and panelLockActive of previous state * D - reset settings to defaults: sleepModeActive = 0, panelLockActive = 0, nightLightActive = 1, cleanCycleWaitTimeMinutes = 7 * L0 - panel lock off: panelLockActive = 0 * L1 - panel lock active: panelLockActive = 1 * N0 - night light off: nightLightActive = 0 * N1 - night light on: nightLightActive = 1 * P0 - turn power off: unitStatus changes = OFF; on the next report from the unit, powerStatus changes to NC and cleanCycleWaitTimeMinutes shows as 7; device is still wifi connected, but won't respond to any commands except P1 (power on), sleepModeActive and panelLockActive reset...
10. Troubleshooting Step-By-Step Guide - Litter-Robot 3
Oct 18, 2016 · The unit should perform an initial Clean cycle: the Globe will rotate counterclockwise to the Dump position, then rotate clockwise past the Home ...
Our convenient Litter-Robot 3 troubleshooting guide helps solve common and not-so-common problems with your unit. Learn how to quickly fix your Litter robot 3.
11. Litter Robot III Open Air Troubleshooting - All 3 Lights ...
Dec 20, 2018 · If the Litter-Robot 3 cannot find the Dump and/or Home position, the control panel will display 3 lights blinking.
Check out our video on how to fix the 3 blinking lights on your Litter-Robot Open Air III.
12. Litter-Robot 4: Light codes guide
If your unit's light bar is blue with two flashing yellow lights, this indicates that the scale has been triggered for more than 30 minutes. Remove excess ...
Discover solutions for all Litter-Robot 4 light codes in our comprehensive guide. Find quick fixes and get your Litter-Robot working perfectly again. Click now!
13. [PDF] Litter-Robot 3 Manual
You can cancel the timer. (red light) by pressing Reset. Red Light Flashing: Cat Sensor Fault ... Cannot find Dump position. The unit will continue to function in ...
14. Litter-Robot 3 Troubleshooting: What Do The Lights Mean?
Jul 22, 2020 · Then hit the Reset button to reset the cat sensor. Check out our Litter-Robot 3 red light flashing troubleshooting guide. Some litters are ...
Litter-Robot troubleshooting means learning about Litter-Robot lights: flashing blue light, flashing red light, blue and yellow lights, and more.
15. Litter Robot Troubleshooting: Fixing Common Litter-Robot 3 Issues
Apr 25, 2016 · Reassemble the Globe back in the Home position. If you sense its weight may be imbalanced, gaze into the litter pocket through the screen. Check ...
Need help with your Litter Robot 3 issues? These are the most common problems and step-by-step ways to fix them.
